Prepare for a massively long video!!! Some shortcuts: Proper ALC 0:58 Microphone Etiquette 3:05 Connecting Mics and Mixers 4:31 Using your mixer 5:23 Unboxin…

25 replies
  1. shaolinskunks88
    shaolinskunks88 says:

    im having problems setting up my microphone, i do gameplay videos when i
    playback my video on my laptop my voice is soo quiet and low i can hardly
    hear myself and the volume switch wont go no higher, and if i turn the gain
    too high it makes my voice loud but i get awful sounds and like an echo of
    my voice. so frustrating. any tips or advice of what im doing wrong. i have
    bought a tried a few mixers and are all doing same thing??? atm i have
    behringer enyx 502

    Reply
  2. RadioHamGuy
    RadioHamGuy says:

    Good video Sterling. I have been using a GM-5 Heil mic for many years now
    with good results and recently just added an EQ-Plus by w2ihy and getting
    good reports so far but I am still tweaking a little to find the best
    settings for my voice but seems great so far.

    Reply
  3. Sterling Coffey
    Sterling Coffey says:

    Thanks for watching and subbing! I use a run-of-the-mill Canon 300 ELPH
    point and shoot. Very nice stereo audio, 1080p video, image stabilization,
    but lacks elsewhere — like the zoom chatters when you use it during video,
    the mic is susceptible to wind, and it likes to defocus. I got
    advertisements on my videos in hope I can save up for a professional
    camcorder…maybe in 5 years at this rate haha!

    Reply
  4. Sterling Coffey
    Sterling Coffey says:

    Phantom power is for powering condenser microphones. They use an element
    that requires a voltage (usually 48v) and a small amount of current to
    power the mic. Without it, no sound comes through. Dynamic mics on the
    other hand work completely mechanically, and require no power. I turn off
    phantom power because I’m using the PR40, a dynamic mic. The MXL990
    conversely is a condenser, and requires it.

    Reply
  5. Sterling Coffey
    Sterling Coffey says:

    Nope — sound mixers are completely unnecessary, as you could wire a good
    Heil mic right into most rigs; they’ll require some sort of interface
    though, especially with Icom rigs. A mixer is nice, though, because it
    allows me to use any mic, send audio anywhere, adjust levels, use condenser
    mics (because of phantom power) and all that fun stuff.

    Reply
  6. citabrianut
    citabrianut says:

    I’m amazed at how this young man has amassed so much equipment in his
    “Shack!” My attention was drawn to the Collins R390A Receiver sitting to
    his left on the second shelf. I used that very same receiver (Along with a
    Hammarlund SP600JX) when I was a Morse Intercept Operator in the USAF back
    in the late 60’s. Excellent receiver and probably the BEST piece of
    equipment in the entire video!

    Reply
  7. Sterling Coffey
    Sterling Coffey says:

    hahahahahahah YES, I am telling you to remove your head from your rectum. I
    can only assume you’re a CB radio fan, hence you’re saying an Astatic
    microphone is better than a Heil. I don’t doubt it, but the fact that Heil
    sells to top performers, broadcast stations and so on, serves reason to
    believe they are two different companies with two different audiences. CB
    Troll be trollin h*m radio videos. Watch out for brain cancer from them CB
    radio wavez.

    Reply
  8. Mark Thomas
    Mark Thomas says:

    Very helpful! I’m in the process of buying an FT3000D with Heil PR761. I’m
    not planning on using an equalizer so hope I get decent audio. I will keep
    an eye on the ALC and mic gain! Thanks for the tutorial. 73. 

    Reply
  9. johnnieace45
    johnnieace45 says:

    I’ve noticed from working dx stations late evening that when the conditions
    have a lot of phase shifting going on that too much mid range and
    compression is worse than if they simply left it as normal full range.
    Sometimes the lows make it easier for me to understand some characters

    Reply

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.